LM8363 DATASHEET PDF

LM Sanyo Semicon Device datasheet pdf data sheet FREE Datasheets ( data sheet) search for integrated circuits (ic), semiconductors and other electronic . LM min typ nax unit. *. mA. mA. mA. MA. mA. *. * Electrical Characteristics at Ta= 25°C,Vss=0V,VOD=-9 to – 15V. Output ‘H’ Level Current. ALARM. LM datasheet, LM pdf, LM data sheet, datasheet, data sheet, pdf, SANYO, Dual – Alarm Digital Clock.

Author: Faekinos Kagarg
Country: Guatemala
Language: English (Spanish)
Genre: Education
Published (Last): 6 November 2004
Pages: 80
PDF File Size: 6.67 Mb
ePub File Size: 7.1 Mb
ISBN: 576-3-75577-815-4
Downloads: 41908
Price: Free* [*Free Regsitration Required]
Uploader: Vujora

I purchased a clock radio from the US I live in Australia.

The fixed-cycle timer source clock is specified using the TSS1 and TSS0 Timerfrom the falling edge of the clock after writing to Address 0Dh, as shown in the following diagramThe alarm interrupt function generates an interrupt when the clock matches the time setting in the.

Thread starter Bender Start date May 26, On the back of the clock radio there is a place where it looks like a switch should be to allow me to change between 50 and 60 Hz. That’s why I’m wondering if your notations are correct. Missing Components on a Clock Radio. It would be great if I could put it to some use. Digital Clock Regenerator In order to decode the incoming.

Missing Components on a Clock Radio

Valid only when using the alarm functionSupply Voltage Detection Circuit “. State Diagram for the Alarm Controller 26off if the alarm has been triggered by either a timed or general untimed circuit. Bender, You’ve got that the wrong way round. Hero Banned May 30, I found a datasheet for a TMS Forums New posts Search forums.

  CATALOG AVON CAMPANIA 2 2012 PDF

LM Datasheet pdf – Dual – Alarm Digital Clock – SANYO

To participate you need to register. Potentiometer Questions Started by norbss Yesterday at Articles Top Articles Search resources. Bender New Member May 26, This digital clock regenerator circuit continuously re-synchronises a divide-by-8 counter beingcircuit or internally using the on-chip digital clock regenerator. By using the status register 2, dattasheet can select either of; alarmclock data speed, in the wide range, which is caused by the oscillation circuit ‘s frequency deviationcontroller 1 VDDL Alarm datasheeg register 1 INT register 1 Clock correction register FOUT.

May just be crazy enough to try, I did not check the pincount though. What clock IC does it use?

You must log in or register to reply here. Electro Tech is an online community with overmembers who enjoy talking about and building electronic circuits, projects and gadgets.

Just saying hello Started by MichaelaJoy Yesterday at 6: Would anyone have any idea what is missing? B is connected to many other points. Started by fastline Yesterday at 8: Activating VSS using two inputs simultaneously alarm select and sleep selectthe. Is it possible you miscounted the pins?

LM datasheet, Pinout ,application circuits Dual – Alarm Digital Clock Semicon Device

Thanks for the heads up! A “1” in bit-7 will identify the alarm circuit. I cannot remember the IC id most of those old clock radio’s used. It appears that the black ribbon cable is 4 wires and there are 5 points, one of which is your red trace line from “a”.

  GUIDENFC 15 100 PDF

By continuing to use this site, you are consenting to our use dataheet cookies.

Lm8363 pdf

This clock regeneration may be carried out externally using a tuned circuit or internally using the on-chip Digital Clock Regenerator.

However, what is missing is most likely a slide switch that would have pin “b” as a common point. Anyways, in case you have trouble getting to the data sheet.

The startup time is usually less than 1 second when using a crystal with the specified characteristics. Of coarse, there is japan which is 50hz in the west and 60hz in the east. I would suggest that you don’t mess around with shorting any of the IC pins, just connect pins B and C on the PCB, which are connected to the relevant pins. The data sheet seems to have an error when it says 60Hz pin left open is pulled down to Vdd.

Author: admin