Gauging of hexagon sockets (ISO ); German version EN ISO ISO Gauging of hexagon sockets. standard by International Organization for Standardization, 01/15/ View all product details. Buy NF EN ISO Gauging Of Hexagon Sockets from SAI Global.
|Published (Last):||25 May 2005|
|PDF File Size:||16.88 Mb|
|ePub File Size:||10.87 Mb|
|Price:||Free* [*Free Regsitration Required]|
In downloading this file, parties accept therein the responsibility of not infringing Adobe’s licensing policy. Acceptability Acceptance procedure is covered in ISO NOTE Particular attention is drawn to the note in Table 233429 and to Table 3 concerning the limitation on ultimate tensile load.
Intermediate nominal lengths according to ISO are permissible.
23249 undated references, the latest edition of the referenced document including any amendments applies. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. Draft International Standards adopted by the technical committees are circulated to the isi bodies for voting.
Up-to-date lists and bibliographical references concerning such ido standards may be obtained on application to the Central Secretariat or to any CEN member. Symbols 23492 designations of dimensions are defined in ISO This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Julyand conflicting national standards shall be withdrawn at the latest by July For dated references, only the edition cited applies.
Adobe is a trademark of Adobe Systems Incorporated. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s member body in the country of the requester. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.
EN ISO 内六角平圆头螺钉 – MBA智库文档
Technical Committee Mechanical fasteners Publisher and printing: Hexagon socket button head screw ISO – M12 40 – They shall nevertheless meet the other material and property requirements for the respective property class specified in ISO This third edition cancels and replaces the second edition ISO Alternative form of socket permissible For broached sockets which are at the maximum limit of size the overcut resulting from drilling shall not exceed of the length of any flat of the socket which is.
The main task of technical committees is to prepare International Standards. If, in special cases, specifications other than those listed in this International Standard are required, they should be selected from existing International Standards, e. A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. Endorsement notice The text of ISO International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
The work of preparing International Standards is normally carried out through ISO technical committees.
ISO – Gauging of hexagon sockets
In accordance with Adobe’s licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In addition, when full-size screws are loaded using the type of testing fixture illustrated in ISOthey shall withstand, without fracture, the minimum ultimate tensile loads given in Table 3.
ISO shall not be held responsible for identifying any or all such patent rights. Table 3 — Minimum ultimate tensile loads for hexagon socket button head screws of the values specified in ISO Thread Property class 8.
NBN EN ISO 23429
Requirements for iiso applied zinc flake coatings are covered in ISO Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee.
All rights reserved; No part of this publication may be reproduced or utilized in any form or by any means — elec- tronic, mechanical, photocopying or any other data carriers without prior permission from ON!
Every care has been taken to ensure that the file is suitable for use by ISO member bodies.