HT12E ENCODER DATASHEET PDF

HT12E Encoder IC can be used only with its pair HT12D. These two ICs together form an Encoder and Decoder pair. Fri, 12 Oct GMT ht12e encoder ic ht12e datasheet pdf – HT12E is an encoder integrated circuit of. 2 12 series of encoders. They are. HT12E is a series encoder IC (Integrated Circuit) for remote control applications. It is commonly used for radio frequency (RF) applications. By using the.

Author: Kagami Darr
Country: Spain
Language: English (Spanish)
Genre: Career
Published (Last): 1 February 2006
Pages: 82
PDF File Size: 13.61 Mb
ePub File Size: 18.66 Mb
ISBN: 382-7-92898-503-7
Downloads: 44448
Price: Free* [*Free Regsitration Required]
Uploader: Yolmaran

The IC is has a wide range of operating voltage from 2.

Choosing Encoedr For Robots. Interface SD Card with Arduino. Arduino based GPS receiver. It is very important that your Decoder should also have this same address for them to talk to each other. Transmission enable; active low. They can also be connected to switches to manually encodwr and receive data. This data should be sent to the HT12D enxoder decoding, it can either be sent directly through a wire or by using a wireless medium like RF or IR.

These are the 8-bit address bits, which is used to protect your data. Submitted by admin on 30 October The Encoded 12 bit output data can be obtained from this pin. This oscillator can be used by connecting these two pins through a 1M Resistor.

They are paired with 2 12 series of decoders for use in remote control system applications. This pin has to be connected to Ground 0V to enable the Transmission.

These two ICs together form an Encoder and Decoder pair. We should set the bits in same pattern on Encoder and Decoder IC to pair them. You can know to set up the Datssheet after this from here.

  BPMN 1.0 POSTER PDF

A basic connection encoddr for the HT12E IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. For decoding a data the IC will requires an oscillator, luckily this IC has one in-built.

HT12E Encoder IC

This cycle is repeated as long as TE is kept low. The IC has a built in oscillator. Virgin Galactic — Commercial Space Flight. It is mainly used in interfacing RF and infrared circuits. These four pins are used to send data, the data encoded here dataasheet be decoded on HT12D IC sharing the same address bits. Choosing Battery for Robots.

In this image I have made all four data bits as zero lowwhen this is decoded we will get the same kind of bits on the output side of HT12D, similarly we can make any changes on these 4-bits and they will be reflected on the output side of the HT12D decoder IC.

This high-density System-in-Package SiP integrates controller, power switches, and support components. SPI Module of Arduino. Connected to the Ground eatasheet circuit. The 4-bit data that has to be sent has to be given to the pins AD0 dagasheet AD1 and an address of 8-bit has to be set using the pins A0 to A7.

So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data. It encodes the 12 bit parallel data into serial for transmission through an RF transmitter.

  ENNYIT KELLENE TUDNOD MATEMATIKBL PDF

TL — Programmable Reference Voltage.

HT12E Encoder IC | HT12E Datasheet | Pin Diagram & Description

Supply voltage; 5V 2. As soon as TE returns to high, the encoder output completes its final cycle and then stops. HT12E is an encoder integrated circuit of 2 12 series of encoders. So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you.

In the above circuit I have set the 8-bit address data as 0b, by connecting encodfr address pins to ground. HT12E begins a 4-word transmission cycle upon receipt of a transmission enable. Interface GPS with Arduino. If you want security you can connect any of the 8 pins to 5V to make it high. The encoded bit can be obtained from the Dout pin pin What is Web Browser.

HT12E has a transmission enable pin which is active low. Simply put, HT12E converts the parallel inputs into serial output. Can range from 2. Skip to main content. Pull the Transmission Enable pin pin 14 to ground to activate transmission. These 12 bits are divided into 8 address bits and 4 data bits. The primary function of HT12E is to encode a bit and send it out through the output pin.

Can be used in Home automation for short range remote switching Safety systems like Burglar alarm encode, Smoke or Fire alarm system etc.

Author: admin