Find the user manual and the help you need for the products you own at ManualsOnline. I got an old laptop model MA2 without powersupply. SetIP command to see and change the IP addresses of the console. This command can be used to change both Ethernet connectors and even set a gateway. Requirement: STP (shielded twisted pair) cable with RJ45 connector, min. Cat 5e . To connect Ethernet port 1: Connect one end of an Ethernet cable to the.
|Published (Last):||25 April 2011|
|PDF File Size:||7.11 Mb|
|ePub File Size:||16.48 Mb|
|Price:||Free* [*Free Regsitration Required]|
Did you get a resolution? Mayo Hardware Fri May 21, Mayo Hardware Mon Aug 23, It looks like it marked P1 or P If no resistance, the Jack is bad. I also notice that the Gateeway charge indicators do not lights with the battery charged The outlet working fine good ground, checked the power supply getting DC, ok lets check the continuity.
gateway ma2 upgrades Computers & Internet Questions & Answers (with Pictures) – Fixya
In the title bar of the menu you can see the current status of the console. When the console is standalone, then tap the green input field next to “Station IP”. Upon further review, it appears that if I jump the post to the left leg of the marked diode, It registers the battery as charging and is able to power on. Open topic as PDF Version 3. Select different version – latest – 3. With the battery on it will chard the battery as long as the monitor is connected.
If not then look at the caps in the area.
Currently I have a charged working battery, and its the only way i can run the laptop, but not for long. Sorcerer Tue May 11, Table of contents of this topic hide. All I see left on the chip is 04, the rest is blown. I’m trying to picture this in my mind. Mayo Hardware Tue Mar 29, gatewag Again – glad I could help.
Mayo Hardware Sat Jul 24, I’ll attempt to re-create the same test here. If I forget send a reminder in a couple of days. You must log in or sign up to reply here.
Similar Threads – can’t seem figure. Mayo Hardware Sat Aug 14, Good to see that you never gave up.
I know it takes 3 hands, but you’ll find a way. Still nothing Noot seeing the post above could u email me at nfamar gmail. Though you gave no description of your problem I cannot guess where your problem might be. Anonymous Mon Apr 26, That’s why laptops seem such a breeze to fix.
Hi, I have a gateway MA3 Series laptop that constantly reboots about every 3 seconds, have swapped batteries, swapped ram and remove all drives and hard drive, and and it is still manuaal a rebooting loop.
I can’t seem to figure out what is wrong with this gateway ma2
Hi Grate blog on the mx laptops helped me fix this issue on many units that i was unable to fix in the passed. The chip that the words are on, is the chip to be jumped to. I found your blog a few days ago while looking for a solution to the MA7 power problem. Anonymous Sun Apr 25, There is what looks to be a similar diode on this board just a bit further down from the positive pin on the gatesay shown It now charges the battery and powers the laptop.
Im not sure how to locate which is the Diode to be jumped or which mosfet to check.
I can’t seem to figure out what is wrong with this gateway ma2 | NotebookReview
Hi Mayo, I have the Gateway ma3 and on inspection i see the power diode is blown. Mayo where are the mosfet s located at? Thanks Sam I’ll take a look at a D and see what I can think of. If it is the type with wires, simply remove from connector, short the POS and NEG terminals of the battery connector while pressing the power button.
Any thought on this Help!
I have gayeway on the POS pin to the shield of the dc port. Any other things to check after the ? Damien Sun Apr 25, Blacky Dec 14, So remedy may not always apply. The charge light comes on then goes out. I need to get my Ma3 Battery Charged.
Mayo Hardware Mon Jul 16, Can’t seem to boot from external usb mw2 – XPS 15 boeNov 6,in forum: