eh11a regulator datasheet, cross reference, circuit and application notes in pdf EH11A SOT eh14a regulator eh16a regulator voltage regulator sot Cheap Voltage Regulators/Stabilizers, Buy Directly from China Suppliers:EH11A H11A AZH-ADJ Enjoy ✓Free Shipping Worldwide! ✓Limited Time Sale. Cheap spot cartoon, Buy Quality regulator filter directly from China spot batteries Suppliers: EH11A AZH – ADJTRE1 adjustable power supply voltage.
|Published (Last):||12 May 2011|
|PDF File Size:||4.69 Mb|
|ePub File Size:||6.47 Mb|
|Price:||Free* [*Free Regsitration Required]|
EH11A View Datasheet(PDF) – Diodes Incorporated.
If the multimeter does read a voltage near its rated output voltage, the voltage regulator is functional and is good. The ground pin is pin 2.
If we do not, then the voltage regulator is defective, as it does not do the job it was designed for, which is output a regulated voltage. An adjustable regulator can be tested in the same way. Before we get into how to read the voltages with a multimeter, first we’ll go over the pinout of a voltage regulator, so that you’ll know which pins to read voltages from.
Below is the pinout of the LM voltage regulator: And the regulated output voltage comes out from pin 3 Output. So we’ll now go through specifically how to test a voltage regulator. To test the voltage going into the voltage regulator, we take a multimeter and place it in the DC voltage setting. How To Test a Voltage Regulator A voltage regulator is a device that takes in an input voltage and regulates it down to the voltage that it is rated for.
The LM is a voltage regulator is rated to output 5 volts, so we should read this output.
To measure the output voltage, we place the same multimeter set in the DC voltage setting and now place the positive probe of the multimeter on the output pin of the regulator and the negative probe on the ground pin of the regulator. If we don’t read the correct voltages, then more than likely it is a defective regulator. Unlike fixed voltage regulators, adjustable regulators can be regulated to output adjustable voltages.
The input voltage that needs to be regulated down goes into pin 1 Input.
Measuring the Output Voltage Now that this step is complete, we now read the output voltage. Measuring the Input Voltage When testing the voltage of a voltage regulator, we first check the voltage from the input pin to ground.
We take the probes of the multimeter and place the positive probe normally the red probe on the input pin of the voltage regulator and the negative probe normally black probe on the ground pin. The voltage that we should read should be higher than the voltage the regulator is rated to output.
If we read at the input pin the voltage which we feed into the regulator and read at the output pin the output voltage which the regulator is rated for, then we know that the voltage regulator is good. All a user must do is calculate the output that the regulator should output and perform the same test as is shown above to see whether it is good or defective. A voltage regulator is a device that takes in an input voltage and regulates it down regulatorr the voltage that it is rated for.
How to Test a Voltage Regulator
We should now read a voltage at or about the rated voltage that the regulator is designed for. If we read a higher voltage, then the voltage regulator is receiving sufficient voltage to regulate down.
If the regulator is rated to output 5 volts, then we should read a voltage very near 5 volts coming out from its output.
This is why we do this test. If the regulator isn’t receiving sufficient voltage, of course it will not be able to output its rated regulated voltage.
EH11A AZ1117H – ADJTRE1 adjustable power supply voltage regulator original spot
This is normally volts higher. Being that a voltage regulator passes out a regulated output voltage, the only test we must do to check a voltage regulator is a voltage test. We check the voltage input into the voltage regulator and the voltage output from the regulator. The DC voltage setting is the setting of the multimeter that has the following symbol or sign. As an example, we’ll use the popular voltage regulator, the LM This is to make sure that voltage is, in fact, being supplied to the regulator.