CNX62 DATASHEET PDF

CNX62 Philips Semiconductors datasheet pdf data sheet FREE Datasheets (data sheet) search for integrated circuits (ic), semiconductors and other electronic. This datasheet contains preliminary data, and supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes. Request PHILIPS [NXP Semiconductors] CNX HIGH-VOLTAGE OPTOCOUPLER online from Elcodis, view and download CNX62 pdf datasheet, In Stock.

Author: Mikazshura Narn
Country: Argentina
Language: English (Spanish)
Genre: Literature
Published (Last): 25 February 2017
Pages: 167
PDF File Size: 13.55 Mb
ePub File Size: 15.15 Mb
ISBN: 473-9-55074-489-9
Downloads: 88342
Price: Free* [*Free Regsitration Required]
Uploader: Meztikasa

CNX62 Datasheet PDF – NXP

It is part of the display area by arranging of the display 4, connecting the seven segments a, b, c, d, e, f, g in parallel between them that attrverso 7 resistors will then be connected to the ports 7 of the Microcontroller PIC16FA.

The cathodes 4 are connected to the collector of transistor 4 in function of the switch. Given the characteristics of the photo-coupler, the input signal must not exceed 15V. Completing the PIC circuit: The displays are common cathode type, the 7 segments are connected in parallel and the 7 common lines are connected by means of a resistor to limit the absorption at 7 RBX ports of the PIC, as shown in the wiring diagram.

(PDF) CNX62 Datasheet download

The experiment is cnd62 out, as usual, on a breadboard where all necessary components are housed. The measurement is displayed on 4 7-segment display of the type common cathode negative in common to all 8 LED, adtasheet segments and decimal point. The 4 transistors are activated by 4 RA of the 8 ports cjx62 the CIP by a resistor connected to the base of the same.

  BORDADOS MARJANE SATRAPI PDF

The image above shows the wiring diagram of the digital frequency with four 7-segment display. The datasheet in PDF format, with the technical specifications of the optocoupler, can be downloaded by clicking the icon below.

Then you have the components of the oscillator, quartz and ceramic capacitors. The frequency meter can not measure signals to sine waves, datahseet and saw tooth triangular with a resolution of 0.

As Always, it shown the pinout of the components where you can see the layout of the pins with the initials of its function to facilitate the construction.

Once programmed and arranged on the base PIC proceed with the connections between it and the display section.

Datasheets search archive of electronic components datasheets

The section signal detection and conversion to be measured is composed of the photocoupler IC 1transistor Q 4 and polarization resistors. At this point one realizes the detection section and the conversion of the signal to be measured.

The decimal point in the third displayalways connected by means of a datahseet resistor, is connected directly to the positive supply. English Menu Home electronic components electronic instruments electronic experiments electronic projects graphic symbols theory.

Finally, the capacitor C 1 has the purpose of eliminating any noise present on power cn62, while the resistor R 8 limit the current absorbed by the decimal point placed on the third display.

  ATRAPADA POR LA MAFIA YAKUZA LIBRO PDF

On this page you experience the application of the PIC16FA as 4-digit frequency meter low frequency. C 1C 2 and XT 1 for the oscillator; C 3 to limit noisy eventually present on power supply.

Fixed the photocoupler is connected to the same datasheer that the output of the collector will present the signal datsaheet the same frequency but of form input square wave to be applied to pin 9 of microcontroller. Given the range of measurement, from 16Hz to Hz, the frequency is tested for educational purposes only given the reduced scope. The datasheet in PDF format, with the technical specifications of the PIC, can be downloaded by clicking the icon below.

To download the HEX file, needed to program the Microcontroller, click here.

Your use of the optocoupler electrically separates the signal to be measured by the microcontroller. The displays are enabled one at a time with the multiplexer system by 4 transistors in switch function.

Before you place the microcontroller on the board it is necessary to program the same with datasheeet HEX file, Arrange them later in the page, downloadable by the required link.

Author: admin