ASTM D3183 PDF

This standard is issued under the fixed designation D ; the number 1 This practice is under the jurisdiction of ASTM Committee D11 on. Buy ASTM D Standard Practice for Rubber—Preparation of Pieces for Test Purposes from Products from SAI Global. Buy ASTM D PRACTICE FOR RUBBER – PREPARATION OF PIECES FOR TEST PURPOSES FROM PRODUCTS from SAI.

Author: Dilkis Tasho
Country: Burundi
Language: English (Spanish)
Genre: Spiritual
Published (Last): 19 May 2005
Pages: 236
PDF File Size: 3.70 Mb
ePub File Size: 7.24 Mb
ISBN: 959-8-45576-856-4
Downloads: 51210
Price: Free* [*Free Regsitration Required]
Uploader: Brarr

Your comments are invited either for revision asfm this standard or for additional standards and should be addressed to ASTM Headquarters. In operation the depth of cut should not exceed approximately 0.

Do not aastm out buffing beyond the point where unevenness of thickness has been eliminated. The knife should be lubricated with a mild soap solution to ease the cutting operation. Originally published as D — ASTM D e1.

ASTM D3183 – 10(2015)

A superscript epsilon e indicates an editorial change since the last revision or reapproval. An adjustable slow-feed mechanism is? If this is not possible, use commercial isooctane. The successive cuts should be progressively thinner to avoid over-heating.

d1383 Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Attachments are available for splitting and cutting sections from cable sheathing and hose. Users of this standard are expressly advised that atm of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

NOTE 1—For production quality control, testing within 1 to 6 h after vulcanization may be necessary to monitor plant operation.

This standard has been approved for use by agencies of the Department of Defense. It is important that the wheel should run true, without vibration, and that the abrasive surface based on aluminum oxide or silicon carbide is true and sharp.

  APRECIACION CINEMATOGRAFICA PDF

The buffing may be either against the drum, against one of the pulleys, or against the taut band between the pulleys. NOTE 2—Wheels of to mm 5 to 6-in. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to d33183. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?

The American Society for Testing and Materials takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Equipment should be provided for slow feeding of the material to the abrasive band and for securing the material without excessive deformation Note 3.

Adjustments should be available to vary the thickness of cut, and feed rollers should be provided to transport the material d3138 the knife. In aatm, cuts removing several tenths of a millimetre of rubber are practicable as the heat build up is much lower than with the method of 7. Current edition approved March 30, The abrasive bands should be of textile or paper, or a combination of the two, with the abradant based on aluminum oxide asym silicon carbide bonded to its surface with a resin unaffected by water.

For removal of greater thicknesses of rubber, use the cutting techniques indicated in 7. A number in parentheses indicates the year of last reapproval.

ASTM D – 02 Standard Practice for Rubber—Preparation of Pieces for Test Purposes from Products

Procedures are given for preparing pieces suitable for preparing specimens of the product. Provision should be made for continuous sharpening of the cutting edge. The sheets shall have one of the following thicknesses unless another thickness is technically astk Some skiving machines can separate plies of rubber as in belts, hose, and tires see 7.

  IPA FISIKA GASING PDF

Uneveness of surface may result from contact with fabric components, cutting techniques, or other reasons. Suitable means should be provided for securing the rubber to prevent excessive deformation and for controlled traversing of the rubber pass the abrasive wheel Note 2.

Procedures in this section describe the preparation of pieces from vulcanizates that are too thick, have uneven surfaces, or contain textiles. Clamping devices should be available to secure the rubber. Preparation of Pieces 7.

The grinder should asym equipped with a slow-feed mechanism so dd3183 very light cuts may be made to avoid over-heating of the rubber. If a liquid adtm used, place the rubber so as to permit free evaporation of the liquid. Last previous edition D — Such pieces are used as a source from which specimens are obtained for testing. The pieces shall be prepared in accordance with Section 7. Allow time for the complete evaporation of the liquid before the specimens are cut and tested.

Take care to avoid excessive stretching of the rubber during the separation, by separating a little at a time while the rubber is gripped near the point of separation. The machine consists of a motor- or hand-driven disk cutter of suitable diameter with a movable cutting table that transports the sample d31883 the cutting edge. NOTE 3—Grit sizes of 0. The sheets shall be vulcanized in accordance with Practice D and shall have an equivalent state of vulcanization judged from such properties as can be determined on the product.

Author: admin